Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112

Notice: Undefined offset: 8192 in /home/cubfest/public_html/photos/include/debugger.inc.php on line 112
FarmallCub | Cubfest Photo Gallery - Last additions

 FarmallCub | Cubfest Photo Gallery

Photo host for users of the FarmallCub.com forum
Home > User galleries > Stanton

Last additions - Stanton's Gallery
J_Hook_3.jpg
9 viewsInstalled J hook.StantonSep 30, 2014
Unfinished_Hood.JPG
10 viewsHood was in dire need of stripping. It was 2013 Thanksgiving weekend and the weather was cooperative.StantonSep 29, 2014
Unfinished_Nose.JPG
10 viewsStantonSep 29, 2014
Stripped_Sheetmetal.JPG
10 viewsStripped nose and hood.StantonSep 29, 2014
Manifold_Tap.JPG
9 viewsRented a 2" tap to redress the manifold threads. The existing exhaust pipe had stripped threads and just sat down in the manifold. All those years of wobbling around in there rounded off the manifold threads and/or filled them with black soot. First, I tried using a 2" pipe nipple, but it wouldn't grab and center itself to cut; just kept popping out even with pressure and tapping with a mallet. So, I called the rental shop and rented a 2" pipe tap. Was tough to turn at the end. But do-able.StantonSep 29, 2014
Manifold_Threads.JPG
9 viewsThreads restored. Rental cost was $15 for 3 hours. Couldn't buy a good used manifold for that.StantonSep 29, 2014
BB_001.jpg
10 viewsThe old battery box had a couple nasty cutouts where the battery cables went in and out. Cut out the old openings and squared them up, ready for piecing and welding some new ones in.StantonSep 26, 2014
BB_002.jpg
9 viewsPieced some new sheet metal into the old openings.StantonSep 26, 2014
BB_003.jpg
9 viewsWelded and ground down the old openings.StantonSep 26, 2014
BB_004.jpg
9 viewsTop is marked out on sheet metal with a Sharpie pen.StantonSep 26, 2014
BB_005.jpg
9 viewsEasier to cut the battery cable holes while it's still flat.StantonSep 26, 2014
BB_006.jpg
13 viewsBattery cable holes cut. Ready for bending.StantonSep 26, 2014
BB_007.jpg
14 viewsHooked up the sheet metal bender and with a little effort got this.StantonSep 26, 2014
BB_008.jpg
10 viewsReady for welding.StantonSep 26, 2014
BB_009.jpg
9 viewsWelded the corners and ground them down. Added some "L" brackets with tie-downs.StantonSep 26, 2014
BB_010.jpg
9 viewsReady for some primer and paint.StantonSep 26, 2014
AMMETER_001.jpg
9 viewsRusted old ammeter switch box. Had a large wasp nest in there.StantonSep 26, 2014
AMMETER_002.jpg
9 viewsJust rusty and in need of a good cleaning.StantonSep 26, 2014
AMMETER_003.jpg
9 viewsCleaned up and welded a piece to minimize the wire opening in the bottom. This should keep my little winged "friends" from building any more nests in there.StantonSep 26, 2014
OIL_CAP_001.JPG
9 viewsOld cap as found when purchased.StantonSep 24, 2014
88 files on 5 page(s) 3